Description
Product Description
Diodes permit electrical current to flow in only one direction– from the trailer to the car
Put it inline on the trailer to prevent back feed voltage from trailer battery to wet cell truck battery, it blocks any potential problems.
Diode Type
|
Item Type: 2 input spades and 1 output spade |
Item Type: 2 input spades and 1 output spade |
Item Type: 2 input spades and 1 output spade |
|
Quantity: 1 PC Diode |
Quantity: 4 PCS Diodes |
Quantity: 30FT 4 Way wire harness+6FT power cord+4 PCS Diodes |
|
Function: Combine brake, turn signal, and emergency flashers in same tail lamp filaments |
Function: Combine brake, turn signal, and emergency flashers in same tail lamp filaments |
Function: Combine brake, turn signal, and emergency flashers in same tail lamp filaments |
- Forward voltage (Vf): 510mV@20A
- DC Blocking voltage(Vr):45V
- Average Rectified Output Current (Io): 20A
- Diode configuration: One-way direct current
- Durable And Higher Capacity
- Help Charge The Auxiliary Battery
- Enables Trouble Free Operation Of Your Towed Vehicle Lights
- Prevents Damage To Your Towed Vehicle’s Electrical Components
- Powers Taillights and Turn Signals on Towed Vehicle
RogueGalaxie –
Imported from Amazon. This is not a review of a purchase made on this website.
External marketplace context: Amazon Vine Customer Review of Free Product( What's this? )
Diodes like this a great for electrical projects.
Stfreview –
Imported from Amazon. This is not a review of a purchase made on this website.
External marketplace context: Amazon Vine Customer Review of Free Product( What's this? )
Working great, I used for a set of auxiliary reverse lights on the truck. They work off the factory reverse lights and a switch both. Now when I use the switch, I am not backfeeding in to the reverse light circuit.
Mark –
Imported from Amazon. This is not a review of a purchase made on this website.
External marketplace context: Verified Purchase
Was adapting a remote for a winch to a dump trailer. All the info said to get two diodes to split signal. Saw these and figured to give them a try because they would make wiring easier and they did the trick. Made wiring so easy. Would recommend them for sure.
Mr68K –
Imported from Amazon. This is not a review of a purchase made on this website.
External marketplace context: Amazon Vine Customer Review of Free Product( What's this? )
To diodes packaged in a cute little heat sink. Makes for a clean install. A pic of the product and a pen cap is included to get a sense of the size.The only thing I will knock off a star for is that the tape is not heat conductive, just your typical very high bond strength double sided tape.
Greg –
Imported from Amazon. This is not a review of a purchase made on this website.
External marketplace context: Amazon Vine Customer Review of Free Product( What's this? )
I needed a way to block power from my reverse backup lights so I could power switched flashing warning lights. The Diode kept power from back flowing from this setup. Now when I flip the switch on for the flashing lights, I am not back feeding in to the reverse light circuit. The Diode is only about 1 inch X 1.25 inch and looks to be very well sealed but it has no listing for being waterproof.
Charles C. –
Imported from Amazon. This is not a review of a purchase made on this website.
External marketplace context: Amazon Vine Customer Review of Free Product( What's this? )
Prevents back feeding in a 2 source single output circuit. I question the 2 sided tape, if it gets hot enough to be have a built in heat sink, won’t it melt the tape? My circuit is not continuous, so I don’t expect much heat build up, but something to keep in mind.
Jesus H. Christ –
Imported from Amazon. This is not a review of a purchase made on this website.
External marketplace context: Amazon Vine Customer Review of Free Product( What's this? )
I’m using this to isolate 2 batteries from each other in an RC airplane. It works perfectly. See the picture, the negatives are common and the positives are separated by the diode: this keeps one battery from trying to charge the other and allows either battery to power the plane. Didn’t get hot with 9v during testing, and the airplane runs on 7.6V so I’m pleased.