Description
If you need custom bushings and reamer, please leave us a message, you provide the drawings, I provide the products, and the cooperation is happy!
The carburetor model for this kit:
GM TBIs
Carter Thermoquads
Holley 4-barrels (including muscle car carbs)
Ford (Autolite) carburetors and more
How to use the kit:
1 Remove the throttle shaft, clean the carburetor damper blades and throttle shaft
2 Using a hand-held variable speed drill (recommended bit size is 10.5mm, smaller than the actual aluminum hole 0.1mm), drill the aluminum hole of the carburetor throttle shaft
3 Reaming operation using the 7/16″ reamer included in the kit
4 Insert the front of the brass bushing into the aluminum hole
5 then pass the throttle shaft through the brass bushing
The role of the reamer: improve the accuracy and coaxiality of the aluminum hole
Imported customer feedback
What customers reported
4.0 / 5
38 ratings
Source: Amazon. These reviews were imported from the source marketplace and are not reviews of purchases made on this website.
No structured vehicle fitment data is available. Compare the listing with the vehicle and existing part before ordering.
Exact identity, part numbers, model references, and available compatibility evidence
Buying guidance
Quick decision
An identity-first rebuild kits listing organized around stable product references and available compatibility evidence.
Fit and size notes
- Match the complete identifier, side, position, connector, dimensions, and visible design with the existing part.
- Treat uncertain vehicle notes as a buying aid, not as a confirmed fitment guarantee.
Specification notes
- Canonical product: MP-US-B07JZMPFVP
- Source product ID: B07JZMPFVP
- Category: Replacement Parts / Fuel System / Carburetors & Parts / Rebuild Kits
- Available images: 6
Before you buy
- Match the complete identifier, side, position, connector, dimensions, and visible design with the existing part.
- Treat uncertain vehicle notes as a buying aid, not as a confirmed fitment guarantee.
Garry Buckminster –
Imported from Amazon. This is not a review of a purchase made on this website.
External marketplace context: Verified Purchase
It worked great .
Dan l. –
Imported from Amazon. This is not a review of a purchase made on this website.
External marketplace context: Verified Purchase
Reamer is way to big the bushings fall out. Bushings themselves are also to big i.d. for shafts to fit and seal. I glued the bushings in with gas tank repair and aluminum dust mixed together and peened them in place it works good now. I’d use a drill next time and buy bushings that fit.
Grant Y. –
Imported from Amazon. This is not a review of a purchase made on this website.
External marketplace context: Verified Purchase
While the reamer works fine, the bushings supplied with it are not the correct ones. I had to purchase oilite bushings to use because the ones that cam with it are too thin and are loose in the hole.
MD –
Imported from Amazon. This is not a review of a purchase made on this website.
External marketplace context: Verified Purchase
Almost useless when the initial cutting edge on the reamer was nicked and dull. I did what I could to sharpen and managed to cut/hone one base plate, but I would not use it on another base plate. One star because the bushing were ok.
Jake Blues –
Imported from Amazon. This is not a review of a purchase made on this website.
External marketplace context: Verified Purchase
Actually the OD is just a smidge over 0.430 so maybe the bushing are closer to 10.93mm.Still, they are NOT 11mm OD and they do not have a press fit after using the supplied ream. What I will end up doing is not reaming all the way in so these bushing will not touch the butterflies and JB Weld to hold them in.I.D. compared to my throttle shaft is about 0.004 difference. Other bushings or shafts may vary.
cindy bellerose –
Imported from Amazon. This is not a review of a purchase made on this website.
External marketplace context: Verified Purchase
Works great
LP –
Imported from Amazon. This is not a review of a purchase made on this website.
External marketplace context: Verified Purchase
Reamer cut alright for a moment then quit cutting. I’m not sure if that became clogged with aluminum or what, but just like many others state the bushing dont fit the hole you just made. They fall out. Not only are they too thin a wall on the bushing, they are too big ID. Almost as sloppy as it was before I installed. Dont waist your money. Just go buy a new carburetor and save a headache.
Michelle Timmers –
Imported from Amazon. This is not a review of a purchase made on this website.
External marketplace context: Verified Purchase
Fixed a quadrajet with this