Loctite 7649 Klean N’ Prime: Activator for Anaerobic Adhesives, Decrease Cure Time, Low Temperature, for Inactive Surfaces, Long On-Part Life | 4.5 oz Aerosol Can (PN: 37509-494147), Gold, Small
$21.99 Original price was: $21.99.$20.63Current price is: $20.63.
Rated 4.7 out of 5 based on 303 customer ratings
303 ratingsSource: Amazon
Confirm quantity, package contents, selected variation, current offer details, and store terms before placing the order.
- Need Primer? This primer adhesive is used when both surfaces are inactive, including plated parts, stainless steel, gold, silver, and aluminum (PN: 37509-494147)
- Reliable, Low-Temp Adhesion: Designed and works on all metals, most surfaces, including passive substrates and inactive materials
- Versatile Application: Suitable for valve covers, oil pans, intake manifolds, industrial furnaces, fasteners 0.08” to 0.5” (2.2 mm to 12 mm), and more, including alternators, air conditioning belts, distributor clamps, carburetor screws, and hairline cracks
- Premium Quality: Enhances your vehicle’s style, comfort, and functionality with top-tier products you can trust
- Cut Cure Time: Accelerates cure times for anaerobic threadlockers, sealers, gasketing, and adhesives, even in temperatures below 41°F (< 5°C)
Before you order
- Confirm the part number, position, dimensions, and connector details shown on this page.
- Compare the listing with the part currently installed on your vehicle.
Martin Demel –
Imported from Amazon. This is not a review of a purchase made on this website.
External marketplace context: Verified Purchase
I prepped the main shaft and fifth gear splines off my Dodge NV4500 transmission. It worked so fast, that the Loctite started to cure about 15 seconds after I applied it, causing the fifth gear to stop about halfway while sliding the gear into the main shaft. I had to use a gear pulse to remove it. Then I had to clean all the old Loctite off both surfaces before trying again. Which I did WITHOUT the Loctite Prep!Activator Spray.
Graham –
Imported from Amazon. This is not a review of a purchase made on this website.
External marketplace context: Verified Purchase
I used it secure a bearing on a shaft it made locking compound work so fast you need to make sure it’s ready to go right into place it can set up so fast it stops moving all the way into place
Metal Tronics Inc –
Imported from Amazon. This is not a review of a purchase made on this website.
External marketplace context: Verified Purchase
Works exactly as described
Bill or Sparkey –
Imported from Amazon. This is not a review of a purchase made on this website.
External marketplace context: Verified Purchase
1st off, this product IS NOT intended to clean greasy parts from the get go. It’s merely use as a final clean before assembling your parts. Note: This product contains ACETONE and BUTANE and is highly flammable. Even though Acetone and Butane is not consider extremely toxic on certain web sites, I would consider as such. Meaning, you should be in a WELL ventilated area. I did my work outside and it still can take your breath away. I would highly recommend wearing gloves (e.g. nitrate) while working with it. It will dry the moisture out of your skin. Finally, wear a face shield for eye protection too.I hung my parts [bearing race] on a wire as I sprayed them down and let them dry. It remove any residual oil film on the race. I am using Loctite 660 to glue this bearing in place, due to spinning on its own. All of this is needed to insured that the glue bonds to both metal surfaces for the bearing race.I am well pleased how my project turn out and save me an expensive repair.
day_tripper –
Imported from Amazon. This is not a review of a purchase made on this website.
External marketplace context: Verified Purchase
First, “what’s inside”:Acetone 67-64-1 60 – 100%2-Ethylhexanoic acid 149-57-5 0.1 – 1%Isobutane 75-28-5 10 – 30%Basically: cleaner, catalyst, and propellant.I had a knurled grain mill roller with a right-hand-threaded drive shaft that unfortunately I wanted to run in reverse, which mean the shaft would immediately unthread. I picked up some “permanent” Loctite and this “Activator” and after first cleaning both male and female threads to within an inch of their (or my) lives I applied the “Activator” to both parts, let them sit for an hour to ensure both parts were thoroughly dry, then applied the thread locker and screwed in the drive shaft and then let the assembly sit for 24 hours.Tested the mill with a full hopper of grain (~18 pounds) and it plowed through it all with zero issues. Knock on wood :)Cheers!
James R. Bull –
Imported from Amazon. This is not a review of a purchase made on this website.
External marketplace context: Verified Purchase
I have four non-tapered stainless steel pipe connections on a heating system storage tank. All attempts to seal the fittings with tape or pipe sealants failed until I primed the fittings with this product, and used Loctite thread sealant. One warning, after applying loctite thread sealer, the sealant begins setting within minutes, so if you prep the threads with this product, keep in mind that it quickly cures thread sealant.For Stainless steel pipe fittings, I highly recommend this product.
Bob –
Imported from Amazon. This is not a review of a purchase made on this website.
External marketplace context: Verified Purchase
Did the trick for making a gasket on my JD Gator.
prm –
Imported from Amazon. This is not a review of a purchase made on this website.
External marketplace context: Verified Purchase
Expensive. Only option I could find to speed up curing in cold weather application of lock tite bolt retainer.
maineac –
Imported from Amazon. This is not a review of a purchase made on this website.
External marketplace context: Verified Purchase
Works as expected